Skip to content

Did you know?

You can make us an offer.

The price on the page is not the only way to buy. Tell us what you would like to pay and the studio will reply by email.

  1. 1Choose your piece, metal and diamond.
  2. 2Tell us the price you have in mind.
  3. 3The studio reviews it and replies by email.

Up to 3 offers per piece. No payment details needed to send one.

Carat, size and price · Guide

Diamond Table and Depth Guide: Ideal Percentages

For a round diamond, aim for a 53–58% table and a 59–62.5% depth. Fancy shapes use wider ranges. How table and depth change sparkle and face-up size.

By Steven V., Master Jeweler, 20+ YearsUpdated 2 min read

Diamond Table and Depth Guide: Ideal Percentages
In this guide

Quick answer

Table percentage is the width of the flat top facet divided by the diamond's width. Depth percentage is the stone's height divided by its width. For a round brilliant, a 53–58% table and 59–62.5% depth give strong sparkle and good face-up size.

  • Too deep: the stone faces up small for its weight and can look dark in the center.
  • Too shallow: it looks wide but leaks light and can show a glassy ring or window.
  • Large table: more white brilliance, less colorful fire.
  • Small table: more fire, slightly less brightness.

How table and depth are measured

Both numbers appear on every grading report and are percentages of the average width (for a round, the diameter). A round measuring 6.40 mm across with a table of 3.52 mm has a 55% table. If it is 3.95 mm tall, its depth is 3.95 ÷ 6.40 = 61.7%.

Total depth is made up of three parts: the crown above the girdle, the girdle itself and the pavilion below. A very thick girdle or a steep pavilion raises depth without adding visible size. See the girdle guide for that part of the picture.

Guideline ranges by shape

Fancy shapes do not have one agreed ideal, and a stone outside these ranges can still look lovely. Use them as a first filter, then judge the stone itself.

Shape Depth Table
Round 59–62.5% 53–58%
Oval, pear, marquise 58–64% 53–63%
Cushion 61–68% 58–68%
Radiant 61–68% 61–69%
Emerald, Asscher 60–68% 60–69%
Princess 64–75% 65–75%

Princess cuts run deeper because their square pavilion needs steep angles to return light. Shape-specific advice is in our diamond shape guide.

What goes wrong outside the range

Too deep

Extra depth hides weight below the girdle. A 1 carat round cut at 65% depth faces up at about the width of a 0.95 carat stone with standard proportions, so you pay for weight you cannot see.

Too shallow

Light passes straight through the bottom instead of reflecting back. In rounds this can create a fisheye, a gray ring reflected from the girdle. In fancy shapes it can create a window, a washed-out area in the center where you can see through the stone.

Table too large or too small

A very large table leaves a thin crown with less room for the angles that create fire. A very small table looks dark and closed. In rounds, 54–57% is a comfortable middle.

Do not judge on two numbers alone

Table and depth are a quick screen, not a verdict. Two diamonds with the same table and depth can perform differently because of crown and pavilion angles. For rounds, the cut grade combines all of these. For fancy shapes, check the ratio in the diamond ratio guide and look at a video of the actual stone. Our diamond cut guide lists the crown and pavilion angles to look for.

Each Diamond Studio engagement ring center diamond has an IGI or GIA report showing its table, depth and measurements.

Frequently asked questions

Is a 60% table too big for a round diamond?

It is slightly above the classic range but can still look bright, especially with a good crown angle. Check the overall cut grade before ruling it out.

What depth makes a diamond look biggest?

A depth at the shallow end of the good range, around 59–61% for a round, spreads the weight across the top. Going much shallower gains size but loses sparkle.

Are table and depth on the report exact?

They are measured by machine to a tenth of a percent and are averages, so small differences between two reports of the same stone are normal.

Do table and depth matter for small diamonds?

Less so. In pavé and accent stones the differences are hard to see. They matter most in a center diamond of 1 carat or more.

Put it into practice

Engagement rings to start from

Every design in any shape, metal and carat, with an IGI-certified lab-grown or GIA-certified natural diamond.

Shop engagement rings

Certification

Certified, every piece

Engagement rings come with an IGI or GIA certificate, and every other piece with a Diamond Studio certificate of authenticity.

Still deciding? Ask the people who make it.

Amit, Shimi and Steven V. answer questions from our Fifth Avenue studio, by message or on a call.

Or follow along

Your bag (0)

Your bag is empty.

Start with a ring, then add the matching band and earrings.

Explore engagement rings