Skip to content

Did you know?

You can make us an offer.

The price on the page is not the only way to buy. Tell us what you would like to pay and the studio will reply by email.

  1. 1Choose your piece, metal and diamond.
  2. 2Tell us the price you have in mind.
  3. 3The studio reviews it and replies by email.

Up to 3 offers per piece. No payment details needed to send one.

Ring size and fit · Journal

How to Measure Ring Size

Measure the inside diameter of a ring that fits, or wrap your finger and measure the circumference in mm, then match it to a US ring size chart.

By Steven V., Master Jeweler, 20+ YearsUpdated 4 min read

A set of metal ring sizer gauges with a soft measuring tape and a gold ring
In this article

Quick answer

To measure ring size, find the inside diameter of a ring that already fits, or the circumference of your finger, in millimeters, and match it to a ring size chart. Three ways at home:

  1. Measure a ring that fits: its inside diameter, edge to edge.
  2. Wrap your finger: with a paper strip or non-stretch string, then measure the length.
  3. Use a printable sizer: printed at 100% scale.

A sizing at a jeweler is the most accurate. Measure at the end of the day, make sure the ring will pass your knuckle, and choose the larger size if you fall between two.

A good fit is snug enough that a ring will not slide off when your hands are cold, and loose enough to pass over the knuckle with a gentle push. Each method below gives you a measurement in millimeters; the chart then turns it into a US size. For the widest range of sizes, half sizes and UK and EU equivalents, see our full ring size chart.

Three ways to measure, step by step

1. Measure a ring that already fits

  1. Choose a ring worn on the same finger, on the same hand, that fits comfortably.
  2. Lay it flat on a ruler with millimeter markings.
  3. Measure the inside diameter across the widest point, from inner edge to inner edge, not including the metal.
  4. Match the number to the inside diameter column below.

This is the most reliable home method, because the ring has already proven its fit. A thick or wide ring measures slightly differently from a slim one, so use a ring close in width to the one you are buying.

2. Wrap your finger with paper or string

  1. Cut a strip of paper about 5 mm wide, or use string that does not stretch.
  2. Wrap it around the base of the finger, snug but not tight.
  3. Mark where the end overlaps, then slide the loop over your knuckle to make sure it passes.
  4. Lay it flat and measure from the end to the mark in millimeters. That is the circumference.
  5. Repeat two or three times and use the average.

3. Use a printable ring sizer

Print our printable ring sizer at 100% scale, with no "fit to page" setting, and check the test line with a ruler before you use it. A sizer you cut out and wrap around the finger works like the paper strip; a printed circle you lay a ring on works like the first method.

US ring size chart

US size Inside diameter Circumference
4 14.9 mm 46.8 mm
5 15.7 mm 49.3 mm
6 16.5 mm 51.9 mm
7 17.3 mm 54.4 mm
8 18.1 mm 57.0 mm
9 18.9 mm 59.5 mm
10 19.8 mm 62.1 mm

Each half size adds about 0.4 mm to the inside diameter and about 1.3 mm to the circumference. A size 6.5, for example, is about 16.9 mm across.

How to get an accurate result

  • Measure at the right time. Fingers are slightly larger at the end of the day and in warm weather, and smaller first thing in the morning or when cold. Measure when your hands are at a normal, comfortable temperature.
  • Allow for the knuckle. If your knuckle is larger than the base of your finger, choose the size that slides over the knuckle; a slightly loose ring can be fitted with sizing beads.
  • Size up for wide bands. Bands wider than about 6 mm cover more of the finger and feel tighter, so go up half a size.
  • Between sizes, choose the larger. A ring that is a little loose is comfortable and easy to adjust; one that is tight is hard to remove.
  • Measure the exact finger. Your ring finger on one hand can differ from the other by half a size, and the dominant hand often runs a little larger.

Common mistakes

  • Measuring with cold hands, which reads small.
  • Using stretchy string, or wrapping at an angle, which skews the reading.
  • Pulling the paper too tight, so the ring will not pass the knuckle.
  • Printing a sizer with page scaling switched on.
  • Measuring the outside of a ring instead of the inside.

Men's sizes and professional sizing

The US scale is the same for everyone; men's sizes simply tend to run larger, and men's bands are often wider, which is why the wide-band rule matters. Our men's ring size guide covers comfort-fit bands and wider widths. A jeweler's sizing, with a set of metal sizing rings, is the most accurate option of all, especially if you can ask for sizers in the same width as your band. Try sizes at two different times of day if you can.

Sizing a Diamond Studio ring

Diamond Studio rings are made in US sizes 4 to 10, half sizes included, and every piece is made new to order. If you are not sure of the size yet, choose "Order now and confirm it with us later" and confirm it with us before production. If a ring needs adjusting after it arrives, it can be sent back to us for resizing, though a local jeweler is often quicker. Plain, solitaire and many pavé rings can usually be resized by a size or so; full eternity bands, with diamonds all the way around, usually cannot, so measure carefully for those. Browse engagement rings, or send us a message if you would like help reading your measurement.

Frequently asked questions

How should a ring feel when it fits?

It should slide over the knuckle with slight resistance, sit without spinning much, and come off with a gentle twist. It should not leave a deep mark or feel tight after a few minutes.

Does ring size change over time?

It can. Fingers change with weight, temperature, pregnancy and age, so a size measured years ago may no longer be right. Measure again before ordering a new ring or band.

Can I measure my ring size with a phone app?

Apps that size a ring on screen can give a rough idea, but screens vary. Check the result against a ruler or a printed sizer before you order.

Is ring size the same on every finger?

No. Each finger is a different size, and the middle finger usually runs larger than the ring finger. Always measure the exact finger the ring will be worn on.

What if my measurement falls between two sizes?

Order the larger size, especially for a wider band. Diamond Studio makes half sizes, so a measurement between two whole sizes often matches a half size exactly.

Put it into practice

Engagement rings to start from

Choose a setting, then the diamond’s shape, carat and lab-grown or natural origin.

Shop engagement rings

Certification

Certified, every piece

Engagement rings come with an IGI or GIA certificate, and every other piece with a Diamond Studio certificate of authenticity.

Still deciding? Ask the people who make it.

Amit, Shimi and Steven V. answer questions from our Fifth Avenue studio, by message or on a call.

Or follow along

Your bag (0)

Your bag is empty.

Start with a ring, then add the matching band and earrings.

Explore engagement rings